Really need help

[Shadowomega13]

Hello everyone

I was here to know how to compile smd 3D Models into mld perfectly i keep on getting aborted
a lot so I was wondering is anyone out here came solve this problem here, here is my qc file

$cd "C:\Cloud Strife GMOD Test"
$modelname "Cloud Strife.mdl"
$model "Cloud" "Cloud1_reference.SMD"
$cdmaterials "Cloud Strife GMOD Test\mymodel"
$surfaceprop "flesh"

$sequence idle "Cloud2_reference" ACT_IDLE 1 loop fps 30.00
$sequence ragdoll "Cloud3_reference" ACT_RAGDOLL 1 fps 30.00

$collisionjoints "Cloud4_phy.smd" {

$mass 30.0
$inertia 10.00
$damping 0.50
$rotdamping 1.50
$rootbone "Bone0"

$jointconstrain "Bone1" x limit -50.00 -15.00 0.20
$jointconstrain "Bone1" y limit -35.00 35.00 0.20
$jointconstrain "Bone1" z limit -61.00 61.00 0.20

$jointconstrain "Bone2" x limit -1.00 -1.00 0.20
$jointconstrain "Bone2" y limit 0.00 0.00 0.20
$jointconstrain "Bone2" z limit 3.00 106.00 0.20

$jointconstrain "Bone4" x limit -15.00 15.00 0.20
$jointconstrain "Bone4" y limit -20.00 27.00 0.20
$jointconstrain "Bone4" z limit -82.00 30.00 0.20

$jointconstrain "Bone5" x limit 0.00 0.00 0.00
$jointconstrain "Bone5" y limit 0.00 0.00 0.00
$jointconstrain "Bone5" z limit 3.00 93.00 0.20

$jointconstrain "Bone6" x limit -3.00 3.00 0.20
$jointconstrain "Bone6" y limit -10.00 10.00 0.20
$jointconstrain "Bone6" z limit -39.00 30.00 0.20

$jointconstrain "Bone7" x limit -15.00 15.00 0.20
$jointconstrain "Bone7" y limit -3.00 3.00 0.20
$jointconstrain "Bone7" z limit -8.00 8.00 0.20

$jointconstrain "Bone9" x limit -32.00 32.00 0.20
$jointconstrain "Bone9" y limit -43.00 43.00 0.20
$jointconstrain "Bone9" z limit -50.00 50.00 0.20

$jointconstrain "Bone10" x limit -91.00 95.00 0.20
$jointconstrain "Bone10" y limit 0.00 0.00 0.00
$jointconstrain "Bone10" z limit -155.00 -21.00 0.20

$jointconstrain "Bone12" x limit -48.00 48.00 0.20
$jointconstrain "Bone12" y limit -64.00 64.00 0.20
$jointconstrain "Bone12" z limit -53.00 53.00 0.20

$jointconstrain "Bone13" x limit -91.00 84.00 0.20
$jointconstrain "Bone13" y limit 0.00 0.00 0.00
$jointconstrain "Bone13" z limit -153.00 6.00 0.20

$jointconstrain "Bone8" x limit -30.00 30.00 0.20
$jointconstrain "Bone8" y limit -35.00 35.00 0.20
$jointconstrain "Bone8" z limit -19.00 19.00 0.20

$jointconstrain "Bone3" x limit -3.00 3.00 0.20
$jointconstrain "Bone3" y limit -10.00 10.00 0.20
$jointconstrain "Bone3" z limit -39.00 30.00 0.20

have no idea to compile this properly thx
and I am new here on facepunch do not know if I am suppose to send help on here
}

[highlight](User was banned for this post ("wrong section/undescriptive thread title" - postal))[/highlight]

[Evenios]

a better thread topic would be about the problem you have not just "really need help".....