[h2]this is a fucking tokyo marui mp5-fucking-hkslap-a4[/h2]
[URL=http://s1336.photobucket.com/user/dwt110/media/DSC_0875_zps30499b5b.jpg.html][IMG]http://i1336.photobucket.com/albums/o644/dwt110/DSC_0875_zps30499b5b.jpg[/IMG][/URL]
[B]Introduction[/B]
MP5s are pretty fucking cool because you can HK slap them they shoot 9x19 parabeallubium german bullets and they are german so yeah they are neat. gsg9 and SAS use them also so yeah and you can HK slap them which is fun.
Did I mention you can HK slap them?
[B]First Impressions[/B]
Well for one, when you get your gun, it most likely will have paint on both sides of the receiver selector markings, and it should have a front sight, but besides that, its good old (seriously the design of this gun is like 10 or 15 years old) TM plastic. The metal parts include the: flash hider, front sight post, slight mounts, body pins & screws obviously lol, magazine catch, rear sight wheel thing, and selector. The handguard is pretty damn creaky compared to like a normal gun but whatever. I was told my gun may or may not have had a spring change but idk because I dont have a chrono, but it shoots way better than I was expecting, and the trigger response is pretty nice on a 7.4 lipo. One thing I noted on my gun is that the selector is pretty loose, and the only way to make it tighter is to tighten the grub screw that is on the side of one, otherwise it still clicks into place fine and stays there. Also, the hop up is finnicky when adjusting. Its either too much or too little, kinda hard to get that perfect amount but you can get it if you move it carefully.
[B]Internals[/B]
Its a TM gearbox and TM hop up and everything what the fuck do you expect. If you upgrade it before it breaks you should probably snap your gun in half and quit airsoft forever. Barrel is 229mm long so yeah its not too long its not too short, just dont slap a scope on it and call yourself a sniper.
[URL=http://s1336.photobucket.com/user/dwt110/media/DSC_0876_zps804bebd9.jpg.html][IMG]http://i1336.photobucket.com/albums/o644/dwt110/DSC_0876_zps804bebd9.jpg[/IMG][/URL]
[B]Externals[/B]
Its pretty plastic-y but its really light and still feels solid. Whatever you do, don't trip and fall on the mag because you will explode and break your magazine well and its a bitch to put a new receiver on these guns and take them apart. There is also a cocking handle that doesnt move the bolt (which has fake weld marks), but you can HK slap said handle which is pretty cool. The rear sight has 4 different sized holes, there is no open notch but its okay because I don't aim down my sights. The gun has a full stock so you can put any battery that is the same size or smaller than a 8.4 large brick. The only trades are the "Kal.9mmx19" and "Made In Japan Tokyo Marui". I do believe there are more trades on the top of the receiver that say similar things but mine are melted off
[URL=http://s1336.photobucket.com/user/dwt110/media/DSC_0873_zps140bad19.jpg.html][IMG]http://i1336.photobucket.com/albums/o644/dwt110/DSC_0873_zps140bad19.jpg[/IMG][/URL]
[B]Conclusion[/B]
If you could care less about externals of your gun and care about the internals and want a gun that will last a while then I recommend this gun. It would be great for MOUT or CQB but works well outdoors as well. Also, you can HK slap it.
[URL=http://s1336.photobucket.com/user/dwt110/media/DSC_0869_zps818e578a.jpg.html][IMG]http://i1336.photobucket.com/albums/o644/dwt110/DSC_0869_zps818e578a.jpg[/IMG][/URL]
HK backhand slap
Tell it who's boss
(the gun is)
wait
how do you adjust the hopup if the charging handle doesn't move the fake bolt?
theres a little lever behind the charging handle
Sorry, you need to Log In to post a reply to this thread.
